Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
This post below in relation to A Step-by-Step Guide to Installing a Bathtub is immensely informative. Check it out for your own benefit and figure out what you think about it.
Mounting a bathtub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging project. If the old tub is conveniently available, the job can move rapidly; if you have to open up a wall surface to eliminate the old tub as well as place the brand-new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will need a helper to leave the old tub as well as set in the brand-new one. Ensure you have qualified on your own for the job and also are comfortable trying it. Rather than hiring a service provider to take over a halfway-completed project, it is far better to consider employing one before you begin. Opportunities are you may require a specialist plumber to make tube links.
This short article will certainly assist you mount a new bathtub in your washroom if you have currently acquired a new tub and also don't need to alter the setup of your previous water pipelines.
Your tools as well as product list need to consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, after that the first thing you need to do is detach the water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Safeguard the tap in position with the supplier supplied backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous type should be attached to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Using the two wooden boards under its feet, position the bathtub in the needed setting. The wooden boards are handy in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bath tub until the level checks out degree.
To set up taps, fit the bottom of the furthest flexible tap connector to the proper supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Fill the bathtub and likewise inspect the overflow outlet and also the regular electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub ought to wait until the bath tub has actually been made use of a minimum of when as this will settle it right into its last position.
Getting ready for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to prevent stress on the bath tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the tub with water before securing, to permit the activity experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece of writing on Tools You Need to Install a New Bathtub while browsing the web. Are you aware of another individual who is truly interested in the subject? Please feel free to share it. I am grateful for your time. Don't forget to pay a visit to our website back soon.
Explore Report this page